At the movies, Part I
At the movies, Part III

At the movies, Part II

The second installment of looming cables is on. But before we go on to view the next mini-videos, let's address some of the questions asked from the first set.

Bethany asked: Question: When knitting what you have just demonstrated in a project, do you have the tendency (I know I do, and I've been wondering if I should actually be doing this)to take the slack out of the carry over lines in the back, so that they are nearer to the pegs they are going to end up on? Or do you just leave them loose and long?

Answer: It depends. If I see that my stitches are too loose, I tug gently on each of the stitches, taking out all of the yarn slack off each of the stitches.

Christine asked: I wanted to try your thicker cable that you have posted that uses 6 pegs for the cable instead of three but my yarn simply would not stretch and in some cases I broke it because I was working it over too hard. Do you have any suggestions for keeping the yarn from breaking?

Answer: Excellent question! knitting on a loom stretches out all the stitches and there is very little slack between each stitch. Creating the 6st cables (or larger) is rather complicated. If you are using a yarn with very little elasticity, the stitches are going to be very difficult to twist. One way to make your stitches be more manegeable is to remove the stitches before the cable to a stitch holder doing this will provide you with some slack to cross your stitches for the cable. After you cable, place the stitches back on the corresponding pegs. Another option is to work the row before the cabling loosely--need to plan ahead a bit. Another option: work the stitches before cabling loosely, once you have cabled, go back and take out all the yarn slack off each of the stitches so they are nice and tight.

Christine also asked: on the patterns you show above what is the row repeat.

The 3-st cables that I showed are crossed every other row, e.i: row 1: cable, row 2: work normal. row 3: cable.

Thank you for your questions, keep them coming. If you have any other questions about today's show, drop me a comment and I will address those questions tomorrow.

In today's movie, we will be featuring the 3-st LPC cable and the 3-st RPC cable. They are very similar to the cables we saw previously, except one of the stitches gets purled rather than knitted.

First up, we have the 3-st Left Purl Cross cable (3-st LPC).

How to: cable is over 3 stitches.
  1. Skip peg 1 and peg 2 (with working yarn towards the back of the peg)
  2. Purl the stitch on peg 3. Take this stitch to the cable needle and let cable needle rest in the center of the loom.
  3. Take working yarn to front of peg 1 and peg 2. Knit peg 1 and peg 2. 
  4. Move the stitches as follows: Stitch from peg 2 to peg 3. Stitch from peg 1 to peg 2. Place loop from cable needle on peg 1.
  5. Gently, pull the yarn slack off each of the stitches (if necessary)

Last in the 3-st cable series, we have the 3-st Right Purl Cross cable (3-st RPC)

How to: cable is over 3 stitches

  1. Take stitch from peg 1 to cable needle and place cable needle to center of loom
  2. Knit pegs 2 and 3. Move the stitches from the pegs as follows: from peg 2 to peg 1, from peg 3 to peg 2.
  3. Place loop from cable needle on peg 3. Purl the stitch.
  4. Gently, pull the yarn slack off each of the stitches (if necessary)
Hope you enjoyed the show. Stop by next week for Part III of the cabling show. Next week we will be looking at 4 stitch cables (4-st LC, 4-st RC).

Comments

Feed You can follow this conversation by subscribing to the comment feed for this post.

Jeannie

Thanks again for a fabulous video.

Huggz

The comments to this entry are closed.